 |
Diagnostics -
Self Test |
| |
|
Initialization
Sequences
Whenever the Printer is switched ON, it automatically performs
a series of internal self tests and mechanical initialization sequences.
If any of the parts fail, an error code will appear. Below is a
description of the initialization sequence, describing front panel
messages and the sequence of the Print Quality LEDs, the error messages
and error codes that may appear, and the corrective action.
|
| |
| Self Diagnostics
- Initialization Sequence |
| LED's |
Front Panel Message |
Printer Error
Error Message/Code |
Corrective Action |
|
 Max. Quality
Productivity
Max. Speed |
|
The Printer hangs and nothing else happens |
stall the BootROM or replace it if already installed
(See Memory and
BootROM DIMM's). |
|
Self Test
Please Wait |
Error Memory Config:X
(sometimes only the error code is displayed) |
If X = 7 reseat the DRAM DIMM's, otherwise replace
the DRAM DIMM's (See Memory
and BootROM DIMM's).
|
Max. Quality
Productivity
Max. Speed |
|
Error Memory Test |
Replace the DRAM DIMM's (See Memory
and BootROM DIMM's). |
Max. Quality
Productivity
Max. Speed |
End Self Test |
Max. Quality
Productivity
Max. Speed |
Initializing |
Power Supply Error #1 Contact HP Representative |
The Trailing Cable is not connected correctly. Reconnect
theTrailing Cable. |
| Initializing IO devs |
BootROM checksum failed |
Replace the BootROM (See Memory
and BootROM DIMM's). |
| Spinning up disk |
Boot Failed::1f500XX |
Depending on the last two digits, do the following:
NOTE: If the error is still present after replacing a component,
remember to REINSTALL the component that was first removed before
replacing another component.
01 - Replace the Hard
Disk Drive (HDD). Replace the Main
PCA.
07 - Replace the Hard
Disk Drive (HDD). Replace the Main
PCA.
0E - Replace the Hard
Disk Drive (HDD). Replace theMain
PCA.
02 - Install the Hard
Disk Drive (HDD). Replace the Main
PCA.
03 - Replace the Hard
Disk Drive (HDD). Replace the BootROM DIMM
(See Memory and
BootROM DIMM's). Replace the Main
PCA.
04 - Replace the Hard
Disk Drive (HDD). Replace the BootROM DIMM
(See Memory and
BootROM DIMM's). Replace the Main
PCA.
05 - Replace the DRAM DIMM's
( See Memory
and BootROM DIMM's). Replace the BootROM DIMM (See
Memory and BootROM
DIMM's). Replace the Main
PCA.
06 - Replace the BootROM (See Memory
and BootROM DIMM's). Replace the Main
PCA.
09 - Replace the BootROM DIMM (See Memory
and BootROM DIMM's). Replace the Main
PCA.
0A - Replace the BootROM DIMM (See Memory
and BootROM DIMM's). Replace the Main
PCA.
0B - Replace the Hard
Disk Drive (HDD). Replace the BootROM DIMM (See Memory
and BootROM DIMM's). Replace the Main
PCA.
0C - Replace the BootROM DIMM (See Memory
and BootROM DIMM's). Replace the Main
PCA.
0D - Replace the Hard
Disk Drive (HDD). Replace the BootROM DIMM
(See Memory and
BootROM DIMM's).
0F - Replace Main
PCA.
10 - Replace the Main
PCA.
11 - Replace the Main
PCA.
|
| Spinning up disk...OK |
| Loading firmware.fmw |
Boot FAILED |
Download the Firmware file to the Printer (See Service
Upgrade). |
| Initializing |
Max. Quality
Productivity
Max. Speed |
Initializing L2C |
| Initializing CLK |
| Initializing IO |
| |
BOOTROM ERROR: Current Version:XXX
Necessary Version:XXX
Replace and Restart
|
The BootROM version does not support the firmware
installed on the HDD. Replace the BootROM. |
| |
COMPONENT MISMATCH:
You are running a XXX printer with a XXX disk
Insert XXX disk and restart.
|
The firmware installed on the HDD and the BootROM
personality does not match.
Make sure both parts are either RTL or PS and make sure you do NOT
mix them (See Parts List for Part Numbers). |
Max. Quality
Productivity
Max. Speed |
Initializing
Please Wait
Code rev:XXXXXX
BootROM:XXXXX
RAM present:XXX MB
Hard Disk:XXXX MB
PS Code rev:XXXXX (Only in PS Unit) |
Ready or
Ready for Media |
